If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
There is a manual that contains the methods on how it should be done. When you have decided to do it yourself, you have to prepare the tools that you would be using for it. You should have Allen wrenches or torque wrenches. You should also have sandpaper as it would be used in making it smooth. When you have prepared all of it, you can now start with it.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You must be certain that the diameter on a bar clamp will be able to match on the diameter of that stem. You must be checking it so you could surely avoid some problems. This will not fit into it if both of the diameter will not fit each other. Before you will be buying one, you should check their diameter to avoid wasting some money on it.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You could slide a level to its bar. You could make some adjustments based on your preference when you are uncomfortable with it. This must be placed cautiously. You must bear in mind that the warranty will be invalid when it is broken.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
About the Author:
Read more about Procedures On Installing Profile Design Cobra Bars You Must Follow.
No comments:
Post a Comment